RockBoard RBO POW ISO 9 IEC Adapter
The RockBoard ISO Power Block V9 IEC is an isolated multi-power supply for effects pedalboards, delivering clean, hum-free DC power to up to nine pedals from a single IEC mains input. Nine galvanically isolated transformers and advanced filtering technology prevent high-frequency noise, while individual short-circuit protection keeps the rest of the chain running if one pedal fails.
- 9 isolated transformer slots plus 1 USB-A output (5 V, 2000 mA) for charging phones or powering small accessories
- 3 switchable outputs (9 V / 12 V / 15 V / 18 V) handle modern DSP pedals with higher voltage or current demands
- 3 fixed 9 V outputs at 500 mA and 3 fixed 9 V outputs at 250 mA cover the majority of standard analog stompboxes
- Compact aluminum housing (195 × 88 × 35 mm, 591 g) with international 100–230 V AC input for worldwide touring
RockBoard ISO Power Block V9 IEC — Clean Isolated Power for Modern Pedalboards
The RockBoard ISO Power Block V9 IEC is a multi-power supply designed to replace a tangle of individual wall-warts and daisy chains with one quiet, central power source for an effects pedalboard. Built around nine galvanically isolated transformers and a single 5 V USB-A port, this model powers up to nine pedals simultaneously without the high-frequency noise that plagues cheaper supplies. The advanced filtering technology used in each DC slot is specifically engineered to suppress the kind of digital whine that ruins otherwise clean guitar and bass tones.
For players running mixed pedalboards that combine vintage 9 V analog drives with modern 18 V DSP units, the V9 IEC delivers the voltage flexibility those rigs demand. Each output is individually protected against short circuits, so a fault on one pedal will not take down the rest of the chain — a critical safeguard on stage and in the studio.
Standout Engineering: Isolated Transformers and Per-Slot Protection
What separates this supply from generic multi-output bricks is the use of nine individual isolated transformers rather than a shared bus, which eliminates ground loops between pedals. Each of the nine DC slots also has its own short-circuit protection and a dedicated status LED, so a problem on one channel is immediately visible without affecting the remaining outputs. The 5 V USB-A port adds practical versatility for charging a phone, powering a small LED light, or running a compact accessory during a gig.
Power Output Configuration — Voltage and Current Flexibility
Voltage and current are the two numbers that determine whether a power supply can actually run a given pedalboard. The V9 IEC splits its nine outputs into three groups so that analog 9 V drives, mid-current digital pedals, and high-voltage DSP units can all be powered from one box.
- Switchable Outputs (×3): 9 V DC at 500 mA / 12 V DC at 375 mA / 15 V DC at 300 mA / 18 V DC at 250 mA — covers everything from standard drives to 18 V DSP pedals.
- High-Current 9 V Outputs (×3): 9 V DC at 500 mA — ideal for current-hungry analog and digital pedals that need extra headroom.
- Standard 9 V Outputs (×3): 9 V DC at 250 mA — a perfect match for typical drive, modulation, and time-based stompboxes.
- USB-A Output: 5 V DC at 2000 mA — charges phones or powers small accessories directly from the supply.
Build, Connectors, and Portability — Built for the Road
A pedalboard power supply lives at the bottom of a board, gets kicked around in transit, and has to survive years of cable swaps. The V9 IEC is housed in a compact aluminum enclosure with a standard IEC mains inlet, so any compatible country-specific power cable can be plugged in directly without an extra adapter brick.
- Dimensions: 195 × 88 × 35 mm — slim profile fits beneath most pedalboards including RockBoard frames.
- Weight: 591 g — light enough to mount under a board without affecting balance.
- DC Connectors: 2.1 × 5.5 mm barrel, center-minus polarity — the industry standard for most stompboxes.
- Mains Input: 100–230 V AC, 47–63 Hz — international voltage range for touring musicians.
Who Is It For — Pedalboard Builders Who Need Quiet, Reliable Power
The RockBoard ISO Power Block V9 IEC is the right choice for guitarists, bassists, and keyboard players building mid-sized pedalboards with a mix of analog and digital pedals who need clean, isolated power without the noise and ground-loop problems of daisy-chained supplies. It suits players running six to nine effects who want one IEC cable into the board instead of a wall full of individual adapters, and it is particularly valuable for anyone using 12 V, 15 V, or 18 V pedals alongside standard 9 V units. The included set of nine 60 cm RockBoard flat power cables makes installation straightforward, while the 5 V USB port covers the small accessories that often clutter a stage setup.
Tip
Broj izlaza
Paket sadrži
Adapter uključen
Ne
Širina (mm)
88
Dubina (mm)
195
Visina (mm)
35
Neto težina (kg)
0,591
Zemlja porekla
Kina
Dokumenti
Uputstva za korišćenje
Informacije o proizvođaču
Bezbednosna uputstva
Pogledaj uputstvo za upotrebu za detaljna bezbednosna uputstva za ovaj proizvod.
